|
Biografi
|
If all lengths were cut the very same, every other length would not match at the top. "Wallpaper patterns may be divided into two primary classes, the ""one-top"" or straight pattern papers, and the ""two-top"" or drop patterns. It is necessary to cut these papers so that the style matches when hung. For this reason factor to consider of the design is necessary prior to cutting such documents. The top of a flower or figure need to not be halved. The paper should be so placed that an entire flower or figure must be left about a 1/2 inch below the photo molding. A ""one-top"" or straight-patterned paper is one in which the design matches on opposite sides of the paper.
They are basic and great for jobs in a kid's bathroom, with patterns that match the bathroom components or bath tub. Prior to cutting the paper, the needed length is to be determined. When this has been done, the paper is unrolled face up. Let us presume that the wall to be covered is 8' high. Allowance should be produced cutting and trimming at the top and bottom. This should be at least 6"". It might be necessary to cut more depending on the pattern. For instance, a paper may have a pattern which is 12"" high.
If there is no room at the top for cutting, the entire pattern needs to be cut off considering that, as has been stated, the top should always have a whole pattern resting about 1/2"" listed below the photo molding or ceiling line. Enabling 6"" for cutting, the length of the strips to be cut will be 8', 6"". The table is 7' long. Take the roll of paper in the left hand, lay it on the table and, with the right hand, pull out 11/2"" from the roll. Let this hang over the end of the table, and then unroll 7', which will cover the length of the table. Examine the style to identify the best location to cut, remembering that the top of the pattern will be about 1/2"" below the picture molding.
This very first piece might be a little bit longer in order to get the top right. The remainder of the paper is cut into equal lengths of 8' 6"". Do refrain from doing this in the restroom. No bath tub is a great work table, even if it is a walk-in tub. A ""two-top"" or drop pattern is one in which the design does not fall straight opposite. In a drop pattern, every other length drops one half of a pattern. If the pattern is 20"" long, for example, the adjacent pattern will be 10"" below this.
It can be seen, then, that a drop pattern paper can not be cut the very same as a straight-pattern paper. If all lengths were cut the very same, every other length would not match at the top This is especially noticeable in little places like bathrooms, where the wallpaper is one of the only things to look at while waiting for the sauna or sitting in the tub. The wallpaper is visible from the shower as well. The simplest way to cut these documents is to take lengths from separate rolls. Cut the very first length as explained for a ""one-top"" pattern. Lay this aside. Cut the next length off the other roll, matching it at the top.
Continue to cut lengths alternately from one roll and the other, keeping the two separated. The very first, third, 5th, etc., lengths will have one top, while the 2nd, fourth, sixth, and so on, will be different. Prior to hanging the first width, the location at which to begin should be determined. This is discovered by deciding which the most popular walls are. They are usually those between windows and over the mantel. Then determine the least noticeable place in the room and prepare the work to complete there, so if a mismatch happens, it will be least visible. If there is no mantel in the space, the first width needs to be hung in between the windows.
Then follow around to the right, covering one side of the room. Return to the window end and paper the other side. By this strategy of procedure, you will always have great light. If you are operating in a restroom with no windows, attempt affixing a brilliant lamp onto the shower tray or the shower doors (this may be tough with frameless shower doors) to get rid of most shady corners. If there is a mantel in the room, the first pieces are put there, considering that it is the most obvious point.
The wall over the mantel is marked so that the paper will be centered. This treatment is as follows: Determine the width of wall over the mantel to find the center. Draw a line through this center. If the area requires 4 widths, put the first width of paper with its center on the center line of the mantel. A complete width is put to the left and right of the center piece. These three widths are short lengths. The staying part will be covered with two partial widths of complete length. Cut these 1/2"" wider than required, so regarding have the edges turn the corner."
|
