|
Biografi
|
The wallpaper is visible from the shower as well. "Wallpaper patterns might be divided into 2 principal classes, the ""one-top"" or straight pattern papers, and the ""two-top"" or drop patterns. It is required to cut these documents so that the style matches when hung. For this reason factor to consider of the style is needed prior to cutting such papers. The top of a flower or figure should not be cut in half. The paper ought to be so put that a whole flower or figure must be left about a 1/2 inch listed below the photo molding. A ""one-top"" or straight-patterned paper is one in which the style matches on opposite sides of the paper.
They are simple and helpful for jobs in a kid's restroom, with patterns that match the restroom fixtures or bathtub. Prior to cutting the paper, the required length is to be determined. When this has actually been done, the paper is unrolled face up. Let us assume that the wall to be covered is 8' high. Allowance should be produced cutting and trimming at the top and bottom. This need to be at least 6"". It might be essential to cut more depending upon the pattern. For instance, a paper may have a pattern which is 12"" high.
If there is no space at the top for cutting, the whole pattern needs to be cut off considering that, as has actually been said, the top should constantly have an entire pattern resting about 1/2"" listed below the picture molding or ceiling line. Enabling 6"" for cutting, the length of the strips to be cut will be 8', 6"". The table is 7' long. Take the roll of paper in the left hand, lay it on the table and, with the right-hand man, take out 11/2"" from the roll. Let this hang over completion of the table, and after that unroll 7', which will cover the length of the table. Take a look at the design to identify the finest location to cut, keeping in mind that the top of the pattern will have to do with 1/2"" below the photo molding.
This very first piece may be a little longer in order to get the top right. The remainder of the paper is cut into equal lengths of 8' 6"". Do refrain from doing this in the restroom. No tub is a great work table, even if it is a walk-in bath tub. A ""two-top"" or drop pattern is one in which the design does not fall straight opposite. In a drop pattern, every other length drops one half of a pattern. If the pattern is 20"" long, for example, the adjacent pattern will be 10"" below this.
It can be seen, then, that a drop pattern paper can not be cut the like a straight-pattern paper. If all lengths were cut the exact same, every other length would not match at the top This is particularly noticeable in small places like bathrooms, where the wallpaper is one of the only things to look at while waiting for the sauna or sitting in the tub. The wallpaper is obvious from the shower as well. The most convenient way to cut these papers is to take lengths from separate rolls. Cut the very first length as explained for a ""one-top"" pattern. Lay this aside. Cut the next length off the other roll, matching it at the top.
Continue to cut lengths alternately from one roll and the other, keeping the two separated. The very first, third, 5th, etc., lengths will have one top, while the 2nd, 4th, sixth, etc., will be different. Before hanging the very first width, the place at which to start should be determined. This is discovered by deciding which the most popular walls are. They are generally those between windows and over the mantel. Then determine the least noticeable location in the room and plan the work to finish there, so if an inequality takes place, it will be least obvious. If there is no mantel in the space, the very first width needs to be hung in between the windows.
Then follow around to the right, covering one side of the room. Return to the window end and paper the opposite. By this plan of treatment, you will constantly have good light. If you are working in a bathroom with no windows, attempt affixing an intense lamp onto the shower tray or the shower doors (this might be hard with frameless shower doors) to get rid of most shady corners. If there is a mantel in the space, the first pieces are placed there, because it is the most conspicuous point.
The wall over the mantel is marked so that the paper will be centered. This treatment is as follows: Determine the width of wall over the mantel to find the center. Draw a line through this center. If the space requires four widths, put the very first width of paper with its center on the center line of the mantel. A complete width is put to the left and right of the center piece. These three widths are short lengths. The staying part will be covered with two partial widths of full length. Cut these 1/2"" wider than required, so as to have the edges turn the corner."
|
