|
Biografi
|
It can be seen, then, that a drop pattern paper can not be cut the very same as a straight-pattern paper. "Wallpaper patterns may be divided into two primary classes, the ""one-top"" or straight pattern documents, and the ""two-top"" or drop patterns. It is necessary to cut these papers so that the style matches when hung. For this factor consideration of the style is necessary before cutting such documents. The top of a flower or figure need to not be cut in half. The paper ought to be so placed that a whole flower or figure must be left about a 1/2 inch below the image molding. A ""one-top"" or straight-patterned paper is one in which the style matches on opposite sides of the paper.
They are easy and excellent for jobs in a kid's restroom, with patterns that match the restroom fixtures or bathtub. Before cutting the paper, the needed length is to be determined. When this has been done, the paper is unrolled face up. Let us assume that the wall to be covered is 8' high. Allowance should be made for cutting and cutting at the top and bottom. This ought to be at least 6"". It may be required to cut more depending upon the pattern. For example, a paper may have a pattern which is 12"" high.
If there is no space at the top for trimming, the whole pattern must be cut off given that, as has actually been said, the top should constantly have a whole pattern resting about 1/2"" listed below the image molding or ceiling line. Enabling 6"" for trimming, the length of the strips to be cut will be 8', 6"". The table is 7' long. Take the roll of paper in the left hand, lay it on the table and, with the best hand, pull out 11/2"" from the roll. Let this hang over the end of the table, and after that unroll 7', which will cover the length of the table. Take a look at the design to identify the very best place to cut, keeping in mind that the top of the pattern will be about 1/2"" listed below the photo molding.
This first piece may be a bit longer in order to get the leading right. The rest of the paper is cut into equal lengths of 8' 6"". Do not do this in the restroom. No bathtub is a great work table, even if it is a walk-in tub. A ""two-top"" or drop pattern is one in which the design does not fall straight opposite. In a drop pattern, every other length drops one half of a pattern. If the pattern is 20"" long, for instance, the adjacent pattern will be 10"" listed below this.
It can be seen, then, that a drop pattern paper can not be cut the like a straight-pattern paper. If all lengths were cut the same, every other length would not match at the top This is particularly noticeable in little locations like bathrooms, where the wallpaper is among the only things to take a look at while waiting on the sauna or sitting in the tub. The wallpaper is noticeable from the shower also. The most convenient method to cut these papers is to take lengths from different rolls. Cut the first length as described for a ""one-top"" pattern. Lay this aside. Cut the next length off the other roll, matching it at the top.
Continue to cut lengths alternately from one roll and the other, keeping the two separated. The first, 3rd, fifth, etc., lengths will have one top, while the 2nd, 4th, sixth, and so on, will be different. Before hanging the first width, the location at which to begin need to be figured out. This is found by choosing which the most popular walls are. They are typically those between windows and over the mantel. Then figure out the least obvious place in the space and prepare the work to complete there, so if an inequality occurs, it will be least noticeable. If there is no mantel in the space, the first width needs to be hung between the windows.
Then follow around to the right, covering one side of the space. Return to the window end and paper the other side. By this plan of treatment, you will always have great light. If you are operating in a restroom with no windows, attempt affixing a bright lamp onto the shower tray or the shower doors (this may be challenging with frameless shower doors) to get rid of most shady corners. If there is a mantel in the room, the very first pieces are positioned there, since it is the most obvious point.
The wall over the mantel is marked so that the paper will be centered. This procedure is as follows: Measure the width of wall over the mantel to find the center. Draw the line through this center. If the space requires 4 widths, place the first width of paper with its center on the center line of the mantel. A full width is put to the left and right of the center piece. These 3 widths are short lengths. The staying part will be covered with two partial widths of full length. Cut these 1/2"" broader than needed, so regarding have the edges turn the corner."
|
