|
Biografi
|
Lay this aside. Cut the next length off the other roll, matching it at the top. "Wallpaper patterns may be divided into two principal classes, the ""one-top"" or straight pattern documents, and the ""two-top"" or drop patterns. It is essential to cut these papers so that the style matches when hung. For this factor factor to consider of the style is essential before cutting such documents. The top of a flower or figure must not be halved. The paper must be so positioned that an entire flower or figure should be left about a 1/2 inch listed below the image molding. A ""one-top"" or straight-patterned paper is one in which the design matches on opposite sides of the paper.
They are easy and helpful for jobs in a kid's bathroom, with patterns that match the restroom components or bathtub. Prior to cutting the paper, the required length is to be identified. When this has actually been done, the paper is unrolled face up. Let us presume that the wall to be covered is 8' high. Allowance must be made for cutting and cutting at the top and bottom. This should be at least 6"". It might be needed to cut more depending upon the pattern. For instance, a paper may have a pattern which is 12"" high.
If there is no space at the top for trimming, the entire pattern should be cut off given that, as has actually been stated, the top needs to always have an entire pattern resting about 1/2"" below the image molding or ceiling line. Allowing 6"" for cutting, the length of the strips to be cut will be 8', 6"". The table is 7' long. Take the roll of paper in the left hand, lay it on the table and, with the right-hand man, take out 11/2"" from the roll. Let this hang over completion of the table, and after that unroll 7', which will cover the length of the table. Analyze the design to determine the finest place to cut, bearing in mind that the top of the pattern will be about 1/2"" below the picture molding.
This very first piece may be a little longer in order to get the top right. The remainder of the paper is cut into equal lengths of 8' 6"". Do not do this in the bathroom. No bathtub is a great table, even if it is a walk-in bathtub. A ""two-top"" or drop pattern is one in which the design does not fall straight opposite. In a drop pattern, every other length drops one half of a pattern. If the pattern is 20"" long, for example, the adjoining pattern will be 10"" below this.
It can be seen, then, that a drop pattern paper can not be cut the like a straight-pattern paper. If all lengths were cut the very same, every other length would not match at the top This is specifically noticeable in small locations like bathrooms, where the wallpaper is one of the only things to take a look at while waiting on the sauna or sitting in the tub. The wallpaper is visible from the shower too. The most convenient method to cut these documents is to take lengths from different rolls. Cut the very first length as explained for a ""one-top"" pattern. Lay this aside. Cut the next length off the other roll, matching it at the top.
Continue to cut lengths at the same time from one roll and the other, keeping the 2 separated. The first, third, fifth, and so on, lengths will have one top, while the 2nd, 4th, 6th, and so on, will be various. Before hanging the first width, the place at which to begin must be determined. This is discovered by deciding which the most prominent walls are. They are normally those between windows and over the mantel. Then determine the least conspicuous place in the space and plan the work to complete there, so if an inequality happens, it will be least noticeable. If there is no mantel in the space, the very first width should be hung in between the windows.
Then follow around to the right, covering one side of the space. Go back to the window end and paper the opposite. By this strategy of treatment, you will constantly have great light. If you are operating in a bathroom with no windows, attempt affixing a brilliant light onto the shower tray or the shower doors (this might be tough with frameless shower doors) to get rid of most dubious corners. If there is a mantel in the room, the first pieces are placed there, given that it is the most conspicuous point.
The wall over the mantel is marked so that the paper will be focused. This treatment is as follows: Measure the width of wall over the mantel to find the center. Draw a line through this center. If the space needs four widths, put the first width of paper with its center on the center line of the mantel. A complete width is put to the left and right of the center piece. These three widths are short lengths. The staying part will be covered with 2 partial widths of full length. Cut these 1/2"" larger than needed, so regarding have the edges turn the corner."
|
