|
Biografi
|
This is especially visible in little places like restrooms, where the wallpaper is one of the only things to take a look at while waiting for the sauna or being in the tub. "Wallpaper patterns might be divided into two primary classes, the ""one-top"" or straight pattern papers, and the ""two-top"" or drop patterns. It is required to cut these documents so that the design matches when hung. For this reason factor to consider of the design is essential prior to cutting such documents. The top of a flower or figure should not be cut in half. The paper ought to be so put that an entire flower or figure need to be left about a 1/2 inch listed below the picture molding. A ""one-top"" or straight-patterned paper is one in which the design matches on opposite sides of the paper.
They are easy and excellent for tasks in a child's bathroom, with patterns that match the restroom fixtures or tub. Prior to cutting the paper, the required length is to be figured out. When this has been done, the paper is unrolled face up. Let us assume that the wall to be covered is 8' high. Allowance needs to be produced cutting and trimming at the top and bottom. This need to be at least 6"". It may be needed to cut more depending on the pattern. For instance, a paper might have a pattern which is 12"" high.
If there is no room at the top for cutting, the whole pattern needs to be cut off since, as has been stated, the top needs to always have an entire pattern resting about 1/2"" below the image molding or ceiling line. Allowing 6"" for cutting, the length of the strips to be cut will be 8', 6"". The table is 7' long. Take the roll of paper in the left hand, lay it on the table and, with the right-hand man, pull out 11/2"" from the roll. Let this hang over completion of the table, and after that unroll 7', which will cover the length of the table. Examine the design to identify the very best place to cut, keeping in mind that the top of the pattern will be about 1/2"" listed below the photo molding.
This first piece might be a little longer in order to get the leading right. The rest of the paper is cut into equal lengths of 8' 6"". Do not do this in the bathroom. No bathtub is a great work table, even if it is a walk-in tub. A ""two-top"" or drop pattern is one in which the design does not fall directly opposite. In a drop pattern, every other length drops one half of a pattern. If the pattern is 20"" long, for instance, the adjoining pattern will be 10"" listed below this.
It can be seen, then, that a drop pattern paper can not be cut the exact same as a straight-pattern paper. If all lengths were cut the exact same, every other length would not match at the top This is especially visible in small locations like bathrooms, where the wallpaper is among the only things to take a look at while waiting on the sauna or sitting in the tub. The wallpaper is visible from the shower also. The simplest way to cut these documents is to take lengths from different rolls. Cut the very first length as explained for a ""one-top"" pattern. Lay this aside. Cut the next length off the other roll, matching it at the top.
Continue to cut lengths alternately from one roll and the other, keeping the two separated. The very first, 3rd, fifth, etc., lengths will have one top, while the second, 4th, sixth, etc., will be different. Before hanging the very first width, the place at which to start must be determined. This is discovered by choosing which the most prominent walls are. They are typically those between windows and over the mantel. Then identify the least noticeable location in the space and prepare the work to complete there, so if a mismatch happens, it will be least obvious. If there is no mantel in the space, the first width must be hung between the windows.
Then follow around to the right, covering one side of the room. Go back to the window end and paper the other side. By this plan of treatment, you will always have great light. If you are operating in a bathroom with no windows, attempt attaching a brilliant light onto the shower tray or the shower doors (this might be tough with frameless shower doors) to remove most shady corners. If there is a mantel in the room, the very first pieces are placed there, because it is the most conspicuous point.
The wall over the mantel is marked so that the paper will be centered. This treatment is as follows: Measure the width of wall over the mantel to discover the center. Draw the line through this center. If the area requires four widths, place the first width of paper with its center on the center line of the mantel. A complete width is put to the left and right of the center piece. These three widths are short lengths. The remaining part will be covered with 2 partial widths of full length. Cut these 1/2"" wider than required, so as to have the edges turn the corner."
|
