|
Biografi
|
It can be seen, then, that a drop pattern paper can not be cut the exact same as a straight-pattern paper. "Wallpaper patterns may be divided into two primary classes, the ""one-top"" or straight pattern papers, and the ""two-top"" or drop patterns. It is needed to cut these documents so that the style matches when hung. For this reason factor to consider of the design is required before cutting such documents. The top of a flower or figure should not be cut in half. The paper must be so placed that an entire flower or figure ought to be left about a 1/2 inch listed below the photo molding. A ""one-top"" or straight-patterned paper is one in which the design matches on opposite sides of the paper.
They are basic and great for projects in a kid's restroom, with patterns that match the bathroom components or tub. Before cutting the paper, the needed length is to be determined. When this has actually been done, the paper is unrolled face up. Let us assume that the wall to be covered is 8' high. Allowance should be made for cutting and cutting at the top and bottom. This need to be at least 6"". It may be required to cut more depending on the pattern. For example, a paper might have a pattern which is 12"" high.
If there is no room at the top for cutting, the entire pattern must be cut off given that, as has actually been said, the top must constantly have a whole pattern resting about 1/2"" listed below the photo molding or ceiling line. Permitting 6"" for trimming, the length of the strips to be cut will be 8', 6"". The table is 7' long. Take the roll of paper in the left hand, lay it on the table and, with the ideal hand, take out 11/2"" from the roll. Let this hang over the end of the table, and after that unroll 7', which will cover the length of the table. Examine the style to identify the very best place to cut, keeping in mind that the top of the pattern will be about 1/2"" listed below the picture molding.
This very first piece may be a bit longer in order to get the top right. The rest of the paper is cut into equal lengths of 8' 6"". Do not do this in the bathroom. No bath tub is an excellent work table, even if it is a walk-in tub. A ""two-top"" or drop pattern is one in which the design does not fall straight opposite. In a drop pattern, every other length drops one half of a pattern. If the pattern is 20"" long, for instance, the adjacent pattern will be 10"" below this.
It can be seen, then, that a drop pattern paper can not be cut the same as a straight-pattern paper. If all lengths were cut the same, every other length would not match at the top This is specifically noticeable in little locations like bathrooms, where the wallpaper is one of the only things to take a look at while awaiting the sauna or sitting in the tub. The wallpaper is obvious from the shower as well. The most convenient way to cut these documents is to take lengths from separate rolls. Cut the first length as described for a ""one-top"" pattern. Lay this aside. Cut the next length off the other roll, matching it at the top.
Continue to cut lengths at the same time from one roll and the other, keeping the two separated. The very first, 3rd, fifth, and so on, lengths will have one leading, while the second, fourth, sixth, etc., will be different. Before hanging the first width, the place at which to begin should be identified. This is discovered by choosing which the most popular walls are. They are normally those in between windows and over the mantel. Then identify the least noticeable place in the space and prepare the work to finish there, so if a mismatch takes place, it will be least visible. If there is no mantel in the room, the very first width needs to be hung between the windows.
Then follow around to the right, covering one side of the room. Return to the window end and paper the other side. By this strategy of procedure, you will always have good light. If you are working in a restroom without any windows, attempt attaching a bright light onto the shower tray or the shower doors (this may be challenging with frameless shower doors) to remove most dubious corners. If there is a mantel in the room, the very first pieces are placed there, since it is the most conspicuous point.
The wall over the mantel is marked so that the paper will be centered. This treatment is as follows: Determine the width of wall over the mantel to find the center. Draw a line through this center. If the space needs 4 widths, put the very first width of paper with its center on the center line of the mantel. A complete width is put to the left and right of the center piece. These 3 widths are short lengths. The remaining part will be covered with 2 partial widths of complete length. Cut these 1/2"" broader than needed, so regarding have the edges turn the corner."
|
